MOT202TSA/MOT202TRMModem User’s Guide0049-0119-000, Rev. A
Configuring the ModemPage 11On the front panel of the modem, there are:c One Power LED and six status LEDs (see page 21)c A rotary test switch (see pa
InstallationPage 12Figure 2-4. Modem Jumper Locations
Configuring the ModemPage 13Table 2-1. Jumper SettingsJumper Function Settings See Page…S1Carrier Detect control-33 dBm-43 dBm14S2Transmit level0dBm-2
InstallationPage 14Note:The jumper positions in the following sections reflect theposition of the jumpers on the modem board when you facethe board as
Configuring the ModemPage 15Jumper S3 − 2-wire/4-wire ModeSettings:2-wire4-wire (default)Jumper S3 configures the modem for 2-wire or 4-wire operation
InstallationPage 16Jumper S5 − Transmit CarrierSettings:Control (default)ConstantJumper S5 places the transmitter under terminal control (default) ort
Configuring the ModemPage 17Jumper S9 − RTS-CTS DelaySettings:8 ms (default)33 ms59 ms219 msJumper S9 configures the modem’s RTS-CTS delay. Four choic
InstallationPage 18Jumper S12 − Soft Carrier Turn OffSettings:None8 ms (default)26 msJumper S12 configures the modem to either turn off the transmitte
Connecting a DTEPage 19Jumpers S14 and S15 − Self Test or Test PatternSettings:1 bps18 bps (default)37 bps75 bps150 bpsJumpers S14 and S15 configures
InstallationPage 20Powering-on the ModemTo supply power to the modem, place the POWER ON switch on themodem back panel to the ON position. The PWR LED
Page iiiContentsCHAPTER 1 INTRODUCTION ...5SUMMARY OF KEY FEATURES...
Page 21Chapter 3 LEDs and Controlshis chapter describes the LEDs and controls on the modem.Front Panel LEDsTable 3-1 describes the LEDs on the modem f
TroubleshootingPage 22Front Panel Test SwitchThe modem front panel has a five-position rotary switch that lets youselect the modem’s operating mode. T
Front Panel Test SwitchPage 23Figure 3-1. Analog Loopback TestFigure 3-2. Digital Loopback TestFigure 1 - Analog Loopback TestDTEDTERECEIVERTRANSMITT
TroubleshootingPage 24Figure 3-3. Self TestFigure 3-4. Transmit Test PatternDTETEST PATTERN TRANSMITTERERROR CHECK RECEIVERPADModemSelf Test Mode4-Wir
Page 25Chapter 4 Troubleshootinghis chapter describes troubleshooting procedures you can use in theunlikely event you encounter a problem with your mo
SpecificationsPage 26Line and Modem TestThe line and modem test verifies the local modem, the remote modem,and the communications line between them. W
Page 27Chapter 5 Specificationshis chapter lists the specifications for the modem.GeneralOperation:2-wire half-duplex or 4-wire full-duplexprivate lin
SpecificationsPage 28Test features:Self Test, Analog Loopback, DigitalLoopback, and Test Pattern TransmitDimensions and WeightWidth:7.00 inches (17.8
Interface Pin AssignmentsPage 29Interface Pin AssignmentsDTE Connector - EIA RS-232-CPin RS-232C Circuit CCITT V.24 Circuit Function1 AA 101 Protectiv
SpecificationsPage 30NOTES
ContentsPage ivCHAPTER 3 LEDS AND CONTROLS ... 21FRONT PANEL LEDS...
Page 31Appendix ACompliancesFCC RuleThis device complies with Part 15A of the FCC Rules. Operation is subject tothe following two conditions: (1) this
CompliancesPage 32Department of Canada StatementThis Class A digital apparatus meets all requirements of the CanadianInterference-Causing Equipment Re
Page 33Appendix BLimited ProductWarrantyTelenetics warrants that the Product sold will be free from defects inmaterial and workmanship and perform to
Limited Product WarrantyPage 34NOTES
Page 5Chapter 1 Introductionhe Telenetics MOT202TSA standalone modem andMOT202TRM rack-mount modem are Frequency Shift Keyed(FSK) modems designed for
IntroductionPage 6ModelsThe Telenetics modem is available in two models:c The MOT202TSA is a desktop modem.c The MOT202RTM is a rack-mount modem that
Contact InformationPage 7Contact InformationFor more information about Telenetics’ MOT202TSA andMOT202TRM modems, or other Telenetics solutions, pleas
IntroductionPage 8NOTES
Page 9Chapter 2 Installing the Modemhis chapter describes how to install the modem.Site PreparationThe location where you install your modem should be
InstallationPage 10Additional Items You NeedTo use your modem, you need the following additional items:c All users: an RS-232 cable to connect a data
Comments to this Manuals